Find the most up-to-date version of JSA – JIS K at Engineering COM PDF – Search results, DOWNLOAD. JIS K STANDARD SDOCUMENTS2. COM jis k standard pdf Specimen. Sample Cutting Dies à ¢â‚¬â€œ. cert. no. ) 03/20/ page 1 of 14 scope of accreditation to iso , Jis K Free Download Here JIS K. physical testing methods .

Author: Mogor Mazugore
Country: Timor Leste
Language: English (Spanish)
Genre: Music
Published (Last): 22 October 2008
Pages: 167
PDF File Size: 14.66 Mb
ePub File Size: 10.19 Mb
ISBN: 499-6-77791-264-4
Downloads: 58822
Price: Free* [*Free Regsitration Required]
Uploader: Dulkis

Inspection is conducted at 2, 50, and points respectively. Standaard D is suitable for hard rubber of which measured figure by Type A 90 and above and Type E is suitable for soft rubber of which measured figure is below However, it is used even now for measurement data or internal management data upon the agreement of concerned parties due to its extensive use historically within the rubber industry. jis k 6301 standard

The most important consideration in using durometers is to select the correct type for purposes 66301 measurement according to the specimen. Constant Loader for Durometer Constant loarder assures uniform test pressure eliminating false readings due to differences between operators in measuring jis k 6301 standard hand.

JSA – JIS K – Physical Testing Methods for Vulcanized Rubber; Errata – 5/ | Engineering

There are 2 kinds of A type for general rubber and C type for hard rubber. Measurement example Hardness is being measured by placing GS G on the sponge sheet.

Night line and highest and lowest limiter equipped for the both are standard. In case there unevenness on the measured face, less flat face because of irregular jis k 6301 standard and deep bump at the bottom, depressed face of durometer is difficult to reach jis k 6301 standard sometimes accurate measurement is not possible. Stxndard is half ball type osibari this is suitable for soft material like soft rubber expanded rubberhardness of spool of textile and film roll to which osibari sticks if it is type A durometer.

It consists of 3 iis of durometer such as Type A for medium stiffness, Type D for high hardness and Type D for low hardness. This is basically equal to JIS K of durometeras only its round up method of spring load figure etc. Dispersion of jis k 6301 standard level can be judged. However, verification is recommended because a significant difference is estimated to be the largest when a stanxard indicates measurement values from 10 to jis k 6301 standard points.

The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.

However, it was used for 50 years as rubber jis k 6301 standard measurement and is still used as test data agreed between concerned persons even now when it is progressed to shift to new JIS and the standard is discontinued. The Pressure foot in contact jis k 6301 standard the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement. This standard is ruled by plastic business field in Japan apart from testing method of hardness of rubber.

JIS K-6301 2

jis k 6301 standard Hardness Tester Selection Chart Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above. Then, long leg type complies with DIN But we distinguish model code as another durometer from conformity of standard point of view.

Pressure foot The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to jis k 6301 standard accurate measurement. Load Tester for Hardness Tester Tester to check load properties of the spring on a durometer Inspection is conducted at 25, 50, and 75 points respectively. Indentor Extension Tester The gauge to check the indentor height on a durometer and the reading indicator mechanism. To jis k 6301 standard of product information.

Two-pointer type max-hand and active hand of Rubber Hardness Tester The stationary set hand max-hand makes the maximum value easier to read js allows the creep characteristics of a specimen. High accuracy and repeatability of the hardness readings are assured by the flexible joint function. Please select according to usage in addition to type A and Type D.

Product Testing & Calibration – Rubber & Rubber Products: Material/Product Testing

JIS Jis k 6301 standard which had been established in and sustaining the base of rubber industry in Japan was discontinued in after the suspended period, as it was not in conformity with ISO, and JIS K was newly established. At that time, deep hole H and long leg type L make measurement possible by making pressed face small or long.

Type E 2 durometer with around half of sponge jis k 6301 standard load figure of type E, and type FO to measure hardness of polystyrene sponge for the level of sponge washing dishes are available.

Our product jis k 6301 standard consists of various types of durometers applicable to specific materials as indicated in the chart above. Type A which is main type tends to indicate higher figure by 1 or 2 points compared with conventional A hardness measurement. GS 4kg weight option Kis