ASTM D is a test method used to study the apparent tensile strength of plastic pipes using a specialized test fixture. The ASTM D standard determines the comparative apparent tensile strength of most plastic products using a split disk test fixture tested under defined. ASTM D TESTING FIXTURE. Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to.

Author: Darr Kinris
Country: Ethiopia
Language: English (Spanish)
Genre: Spiritual
Published (Last): 1 September 2008
Pages: 252
PDF File Size: 16.80 Mb
ePub File Size: 17.89 Mb
ISBN: 453-3-34296-920-9
Downloads: 48940
Price: Free* [*Free Regsitration Required]
Uploader: Ball

Reinforced thermosetting resin pipe may be tested by this standard regardless of fabrication method.

This potential error is analyzed and discussed in detail in References 2 and 3. Astm d2290 Test Fixtures Inc.

ASTM D2290 Plastic or Reinforced Plastic Pipe Tensile Testing Equipment

Although this original Procedure A test method was an ASTM standard from toits popularity has varied over the years. All of these revised procedures use the same general fixture configuration the configuration shown on the right side of Fig.

It is the astm d2290 of the user of this standard to x2290 appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Astm d2290 a question astm d2290 conducting the test for this standard? These former Procedure A specimens are hoop-wound rings of controlled diameter, width, and thickness, viz.

ASTM D Plastic Pipe Hoop Tensile Strength Testing – ADMET

Sources of Additional Information: This test method also is applicable to extruded and molded thermoplastic pipe. Data from this test are useful for research and development, quality control specification and design. Procedure A is now used for testing reinforced-thermosetting resin pipe, Procedure B for thermoplastic pipe of any size, and Procedure C for thermoplastic pipe with nominal diameters of astm d2290.

We offer astm d2290, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique astm d2290.

Historical Version s – astm d2290 previous versions of standard. The test astm d2290 be considered significant for applications differing widely from the load-time scale of the standard test. One criticism is that some bending is induced in the ring specimen at the split.

Force range astm d2290 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models.

Within limits, specimens of varying sizes can be tested using the same astm d2290, by using interchangeable pairs of split astm d2290. Rather than testing a complete ring, two 4″ long segments of the ring are tested together in a special fixture fully defined in ASTM D Friction between the split disk fixture and the ring specimen is also a concern.

In general, this test method is still generally astm d2290 an acceptable test for unidirectional hoop-wound composite rings.

Procedure C has been used on polyethylene and polybutylene pipe to produce results equivalent to Astm d2290 Burst results Test Method D for 4 in. Link to Active This link will always route to the current Active astm d2290 of the standard. Work Item s – proposed revisions of this standard. The version of ASTM D has added a Procedure D, for testing polyethylene pipe with a nominal diameter of 14″ and greater and preferably having a wall thickness 1″ and greater.

Details of the now obsolete fixture and specimen astm d2290 testing filament-wound rings can be found can be found astm d2290 and earlier versions of ASTM D These effects are discussed in R2290 3 and 4.

ASTM D2290 TESTING FIXTURE

Procedure E is used for polyvinyl chloride PVC pipe with a nominal diameter of 14 in. This test method is applicable to reinforced-thermosetting resin astm d2290 regardless of fabrication method.

Give one of our application engineers a call today for help with creating the best budget and testing plan according to ASTM D These various specimen astm d2290 and test procedures are fully defined in the version of ASTM D Asstm 1. The original fixture for testing Procedure A specimens, i. Procedure D is used for polyethylene pipe with a nominal diameter of 14 in. By means of astm d2290 plastic testing expertise and modular product design, we will help ast, the testing solution that is right for you.

The original Procedure B and C specimens, extruded and molded unreinforced plastic specimens and larger diameter extruded plastic pipe, respectively, utilized fixtures astm d2290 the general type shown at the right side of Fig. However, this now deleted original Procedure Astm d2290 fixture, while no longer an ASTM standard, is still used for testing filament-wound composite rings, and the fixture is available from Wyoming Test Fixtures, Inc.

The ASTM D standard determines the comparative apparent axtm strength of most plastic products using a asstm disk test fixture tested under defined conditions and test machine speed. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. We are confident astm d2290 we have astm d2290 you are looking for. Extruded and molded thermoplastic piping is also covered by this test.